keywords: ip pbx voip gateway gsm gateway

× Questions about A400/800/1200 Analog Interface Card

strange "Error 5" loading openvox 1200 driver

8 years 2 months ago #8567 by gusblog
Hi, i have an very strange behavior. will try to explain.
we have 1 x A1200P card version 3.0
with 6 FXO modules
4 FXO rev 1.2
2 FXO rev 1.1
Positions = T1 (rev1.2);T2 (rev1.2);T3 (rev1.2);T4 (rev1.2);T5 (rev1.1);T6 (rev1.2); => Working T5 and T6
the point is only the FXO rev 1.1 are working. only 2 leds apears ON at back in the card. after the driver load.
in the proceess to check fxo modules we start to change some positions :
Positions = T1 (rev1.2);T2 (rev1.2);T3 (rev1.2);T4 (rev1.1);T5 (rev1.2);T6 (rev1.2); => the card give error -5 => any mopule work
Positions = T1 (rev1.1);T2 (rev1.1); then empty; => the card OK => T1 and T2 work
Positions = T1 (rev1.1);T2 (rev1.2);T3 (rev1.1);=> the card give error -5 => any mopule work
Positions = T1 (rev1.1);T2 (rev1.2);T3 (rev1.1);T4 (rev1.2);=> the card give error -5 => any mopule work
the error when not start is :
=============
penVox A1200P passed register test
Module 0: Not installed
Module 1: Not installed
Module 2: Not installed
Module 3: Not installed
Module 4: Not installed
Module 5: Not installed
Module 6: Not installed
Module 7: Not installed
Module 8: Not installed
Module 9: Not installed
Module 10: Not installed
Module 11: Not installed
opvxa1200: probe of 0000:04:06.0 failed with error -5
======================lspci -vvvvv
04:06.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 95d9:0003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <;PERR-
Latency: 32 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 50
Region 0: I/O ports at b000 [ size= 256_]
Region 1: Memory at fe900000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
===================
we tried to change the PCI slot or reset the PC bios,
neither work.
we are using lastest openvox_dahdi-linux-complete-2.6.0+2.6.0.tar.gz +kernel 2.6.18-92.1.22.el5+centos 5
so only work when rev 1.1 are toghether.

Why does this happend ?
apreciate can help to check if the moduoles rev 1.2 are definitly burned or not.

regards
Gus

i] Last edited by gusblog at 2013-2-10 00:29 [/i
8 years 1 month ago #8578 by tim.june
Can you tell me the version of firmware on A1200 board?
Here is some info you may need to know:
http://downloads.openvox.cn/pub/drivers/dahdi-linux-complete/You%20must%20read%20this%20bofore%20downloading%20drivers
If still not work, send me remote access info, i will help U to check it.
This email address is being protected from spambots. You need JavaScript enabled to view it.

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
8 years 1 month ago #8579 by gusblog
Hithanks for your help
the firmware of the card is : 1.2 ( see the attached

the card are working with lastest dahdi version 2.6. recently uploaded.

is posible to update the firmware? how can be done..?

regards

gustavo
Attachments:
8 years 1 month ago #8580 by tim.june
OK, I am glad that the card and the modules is working fine now with OpenVox latest driver.
About the firmware updating, i am afraid it is not possible online. Only send it back for rebuilding firmware can make it happen. If it is working fine with 1.2, no need to upgrade it.
Anything else you need, contact me immediately.

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
8 years 1 month ago #8582 by gusblog
Hi,

thanks for your answer.
as explainedthe card have 6 FXO modules
only 2 are working.

I think others 4 are burned or damaged

my question was, why if i change the positions of modules.
the card daen't detect anyone. neither 2 good ones.

to see details check first post.

regards

Gustavo
8 years 1 month ago #8583 by tim.june
Hi
I have tested the same scene here, and everything is fine [align=center]in above situation[/align][align=center].[/align]
[align=center]If the card and modules in your side are still not working with the latest driver from OpenVox website, I am afraid there should be some hardware faulty issues.[/align]
[align=center]Pls send us S/N for RMA procedure.[/align]

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
Attachments:
Time to create page: 0.055 seconds
Powered by Kunena Forum