A400P OpenVox & 800P other Market in the same Server (

Hi gays

I have a big problem .

I have to install tow card in the same server : one's is A400P ( openVox ) the second is other market ( 800P ) .

I can't make the both work in the same time , because if I download the Dahdi-linux-complete-2.5.0+2.5.0.tar.gz for OpenVox so OpenVox card work fine but not the second ( other market) ,

If I install dahdi-linux-xxxx for the other market the first driver for openVox is erased so the second card work but not the first ( OpenVox )


So what i can do to make work the both ?

How I can tell Linux ( os ) te make this dahdi ( openvox ) for openvox card ?

thank you a lot ti give me a solution

Note : the second card is a china product with 8 fxs openvox modules

i] Last edited by kamel.berrayah at 2013-7-22 09:21 [/i

Hi,
Please give me more details about the card A400 not work. You can add my Skype upper.hua for future communication .

upper

hi
in below the thow cards , in this case openvox work because I installed dahdi opnevox patch

03:05.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Device b700:0003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <;PERR- INTx-
Latency: 16 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at de00
Region 1: Memory at fdcff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: hisax, netjet

03:06.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: OpenVox Communication Co. Ltd. OpenVox A400P 4-port analog card
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <;PERR- INTx-
Latency: 16 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at dc00
Region 1: Memory at fdcfe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: wctdmOPENVOX
Kernel modules: wctdm, hisax, netjet

Please add my skype and provide SSH to me t o check .
upper

Hi

I am always in the same state . It's very difficult to reprogramme wctdm.c ,
Any way to rename the driver of openvox to wctdmopenvox.c ( for exemple ) ?


best regards