keywords:pbx ip pbx voip gateway gsm gateway

× Questions about B100/200/400/800 ISDN BRI Cards

B100 PCI ISDN card no outgoing call

6 years 3 months ago #8935 by mlaszlo
Hi!
Can anyone help me?
I have a following system:
Kernel
Linux(i386)-2.6.18-348.1.1.el5

Elastix
elastix-2.4.0-1
elastix-my_extension-2.4.0-1
elastix-reports-2.4.0-1
elastix-email_admin-2.4.0-1
elastix-system-2.4.0-1
elastix-ha-2.2.0-4
elastix-portknock-0.0.1-0
elastix-framework-2.4.0-1
elastix-im-2.4.0-1
elastix-agenda-2.4.0-1
elastix-a2billing-1.9.4-5
elastix-asterisk-sounds-1.2.3-1
elastix-fax-2.4.0-1
elastix-pbx-2.4.0-1
elastix-callcenter-2.2.0-1
elastix-ZoneMinder-1.25.0-1
elastix-red5-1.0.0-1.rc1.svn4199
elastix-conferenceroom-2.2.0-4
elastix-firstboot-2.4.0-1
elastix-addons-2.4.0-1
elastix-extras-2.4.0-1
elastix-vtigercrm-5.2.1-7
elastix-security-2.4.0-1
elastix-roomx-1.0.0-91

RounCubeMail
RoundCubeMail-0.3.1-12

Mail
postfix-2.3.3-6.el5
cyrus-imapd-2.3.7-12.el5_7.2

IM
openfire-3.7.1-1

FreePBX
freePBX-2.8.1-16

Asterisk
asterisk-1.8.20.0-0
asterisk-perl-0.10-2
asterisk-addons-1.8.20.0-0

FAX
hylafax-4.3.10-2rhel5
iaxmodem-1.2.0-2

DRIVERS
dahdi-2.6.1-4
rhino-0.99.6-0.b2
wanpipe-util-3.5.28-0

After the installation of the B100 ISDN card, incoming calls are OK, but can't operating the outgoing direction. I get a busy system voice prompt.
The outgoing rule with numbering plan is set, What can I do for resolve the problem?
Thanks,
ML
6 years 3 months ago #8936 by hua
HI,

Please provide SSH info to me , you can add me by Skype upper.hua. I will check it .

Best regards
upper
6 years 3 months ago #8937 by mlaszlo
Hi!
I sent the SSH data.
Thanks, ML
6 years 3 months ago #8938 by mlaszlo
Thanks for help!
6 years 2 months ago #8972 by mlaszlo
The incoming calls via ISDN trunk are OK but the B100P and B100E cards don't possible to config for outgoing calls with Asterisk webgui. The outgoing calls operating if I put to the extension.conf the following rules:
<>#&@{}<;>*ä
6 years 2 months ago #8973 by mlaszlo
The rules is the following:
from-test
exten =>_X.,1,Dial(dahdi/g0/${EXTEN})
exten =>_X.,n,Hangup()

and in the extension webgui menu I choose the "from-test" instead of "from-internal".
Why don't possible to config with Asterisk webgui the B100 cards?
Thanks for help.
ML
Time to create page: 0.022 seconds
Powered by Kunena Forum