keywords:pbx ip pbx voip gateway gsm gateway

× Questions about B100/200/400/800 ISDN BRI Cards

help in installing B400p with misdn driver

11 years 9 months ago #494 by yidiyuehan
Hi, I am trying to install B400p card with Misdn driver,
i notice the manual used is asterisk 1.4.11, I want to know does openvox patch hfc_multi.c applies to other asterisk version as well like asterisk 1.2.X and zaptel 1.2.X ?

Has anybody actually tried this before?
11 years 9 months ago #496 by james.zhu
hello, yidiyuechan:
i think it should be no problem. please take note that the version of mISDN should compatible with asterisk 1.2.X. good luck!
james.zhu

11 years 9 months ago #508 by yidiyuehan
Hi, james, I have managed to install B410P card with misdn driver with asterisk 1.2.24.

However I am not sure how to configure the misdn driver. I notice that for Digium card they start misdn driver by /etc/init.d/misdn-init scan/config/start. and they have files in /etc/init.d/misdn-init.conf

But for Openvox B410p card we use /usr/sbin/mISDN scan/config/start, and we have files in /etc/mISDN.conf.

Can you tell me the difference or either of them is fine to fun?

and could you also post the files /etc/asterisk/misdn.conf for Openvox B410p card?

thanks in advance.
11 years 9 months ago #509 by james.zhu
hello, you have to replace the hfc_multi.c for B400P. the mISDN is mISDN-1_1-2. you run the mISDN scan, mISDN config and mISDN start. it will generate mISDN.conf for you. the conf is shown in the user manual( www.openvox.com.cn/downloadsFile/1193650142.pdf ). you also can refer with misdn.org.
Regards!
james.zhu

11 years 9 months ago #510 by yidiyuehan
hi, james, thank you for your fast response, your support is really good. After applying the patch and installing misdn driver, I have made a mistake and apply /etc/init.d/misdn-init scan/config/start.

After that I notice it's not for B400P card, so I apply mISDN /scan/config/start, again. Does it matter?

Below is my server /etc/asterisk/misdn.conf/. could you please check for me:

[general]
debug=0
ntdebugflags=0
ntdebugfile=/var/log/misdn-nt.log
stop_tone_after_first_digit=yes
append_digits2exten=yes
dynamic_crypt=no
crypt_prefix=**
crypt_keys=test,muh

; Users sections
[default]
context=from-zaptel
language=en
musicclass=default
senddtmf=yes
far_alerting=no ; generate ringing for chan_sip and others
allowed_bearers=all
rxgain=0 ; between -8 and 8
txgain=0
te_choose_channel=yes ; some need to set to yes
pmp_l1_check=no
reject_cause=21
need_more_infos=no
nttimeout=yes
method=standard

dialplan=0
localdialplan=0
cpndialplan=0

early_bconnect=yes
incoming_early_audio=no
nodialtone=no
immediate=no ; change to yes if no MSN or DDI numbers
hold_allowed=yes
callgroup=1
pickupgroup=1
presentation=-1
screen=-1
jitterbuffer=4000
jitterbuffer_upper_threshold=0
hdlc=no
echocancel=yes
echotraining=no


[outcall]
ports=1,2,3,4
context=from-zaptel
msns=*
11 years 9 months ago #514 by james.zhu
hello, you can make calls to test it. make sure that you have correct dialplan and mISDN.conf under /etc.
rgs!
james.zhu

Time to create page: 0.021 seconds
Powered by Kunena Forum