CAPI_REGISTER failed - CAPI not installed (0x1009) [No such device or address (6

Hi,

I have done the following steps. but no luck yet.

$ misdnportinfo
Port 1: TE-mode BRI S/T interface line (for phone lines)
-> Protocol: DSS1 (Euro ISDN)
-> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib.
-> childcnt: 2
* Port NOT useable for PBX (maybe there is already a PBX running?)

---

Port 2: TE-mode BRI S/T interface line (for phone lines)
-> Protocol: DSS1 (Euro ISDN)
-> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib.
-> childcnt: 2
* Port NOT useable for PBX (maybe there is already a PBX running?)

---

Port 3: TE-mode BRI S/T interface line (for phone lines)
-> Protocol: DSS1 (Euro ISDN)
-> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib.
-> childcnt: 2
* Port NOT useable for PBX (maybe there is already a PBX running?)

---

Port 4: TE-mode BRI S/T interface line (for phone lines)
-> Protocol: DSS1 (Euro ISDN)
-> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib.
-> childcnt: 2
* Port NOT useable for PBX (maybe there is already a PBX running?)

---

mISDN_close: fid(3) isize(131072) inbuf(0x83cc060) irp(0x83cc060) iend(0x83cc060

$ capiinfo
Number of Controllers : 4
Controller 1:
Manufacturer: mISDN CAPI controller HFCm1/1
CAPI Version: 2.0
Manufacturer Version: 1.0
Serial Number: 0002
BChannels: 2
Global Options: 0x00000018
DTMF supported
Supplementary Services supported
B1 protocols support: 0x00000003
64 kbit/s with HDLC framing
64 kbit/s bit-transparent operation
B2 protocols support: 0x00000043
ISO 7776 (X.75 SLP)
Transparent
Transparent (ignoring framing errors of B1 protocol)
B3 protocols support: 0x00000001
Transparent

0100
0200
18000000
03000000
43000000
01000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000

Supplementary services support: 0x00000033
Hold / Retrieve
Terminal Portability
Call Forwarding
Call Deflection

Controller 2:
...

Controller 3:
...

Controller 4:
...

$ capiinit show
ERROR: no cards configured in /etc/capi.conf

$ capiinit reload
1 mISDN detected mISDN1 -
2 mISDN detected mISDN2 -
3 mISDN detected mISDN3 -
4 mISDN detected mISDN4 -
ERROR: missing config entry for controller 1 driver mISDN name mISDN1
ERROR: missing config entry for controller 2 driver mISDN name mISDN2
ERROR: missing config entry for controller 3 driver mISDN name mISDN3
ERROR: missing config entry for controller 4 driver mISDN name mISDN4

$ pppd call isdn/arcor
Plugin userpass.so loaded.
userpass: $Revision: 1.5 $
Plugin capiplugin.so loaded.
capiplugin: $Revision: 1.36 $
capiconn: 1.13

And here is the syslog output:
last message repeated 3 times
pppd[10030]: Plugin userpass.so loaded.
pppd[10030]: userpass: $Revision: 1.5 $
pppd[10030]: Plugin capiplugin.so loaded.
pppd[10030]: capiplugin: $Revision: 1.36 $
pppd[10030]: capiconn: 1.13
pppd[10031]: pppd 2.4.3 started by root, uid 0
pppd[10031]: capiplugin: phase serialconn.
pppd[10031]: capiplugin: contr=1
last message repeated 3 times
pppd[10031]: controller 1: listen_change_state 0 -> 1
pppd[10031]: controller 1: listen_change_state state=1 event=1 ????
last message repeated 2 times
pppd[10031]: contr 1: listenconf Info=0x0000 (No additional information) infomask=0x144 cipmask=0x0 capimask2=0x0
pppd[10031]: controller 1: listen_change_state 1 -> 0
pppd[10031]: plci_change_state:0x0 0 -> 1 event=1
pppd[10031]: capiplugin: dialing 001XXXXXXXXXX (hdlc)
pppd[10031]: contr 1: listenconf Info=0x0000 (No additional information) infomask=0x144 cipmask=0x0 capimask2=0x0
pppd[10031]: controller 1: listen_change_state state=0 event=3 ????
pppd[10031]: contr 1: listenconf Info=0x0000 (No additional information) infomask=0x144 cipmask=0x0 capimask2=0x0
pppd[10031]: controller 1: listen_change_state state=0 event=3 ????
pppd[10031]: contr 1: listenconf Info=0x0000 (No additional information) infomask=0x144 cipmask=0x0 capimask2=0x0
pppd[10031]: controller 1: listen_change_state state=0 event=3 ????
pppd[10031]: plci_change_state:0x101 1 -> 2 event=3
pppd[10031]: DISCONNECT_IND reason 0x3303 (Protocol error layer 3) for plci 0x101
pppd[10031]: plci_change_state:0x101 2 -> 8 event=9
pppd[10031]: plci_change_state:0x101 8 -> 0 event=11
pppd[10031]: capiplugin: disconnect(remote): "" -> "001XXXXXXXXXX" outgoing (pcli=0x101/ncci=0x0) 0x3303 (0x0000) - Protocol error layer 3
pppd[10031]: plci_change_state:0x0 0 -> 1 event=1
pppd[10031]: capiplugin: dialing 001XXXXXXXXXX (hdlc)
pppd[10031]: plci_change_state:0x101 1 -> 2 event=3
pppd[10031]: DISCONNECT_IND reason 0x3303 (Protocol error layer 3) for plci 0x101
pppd[10031]: plci_change_state:0x101 2 -> 8 event=9
pppd[10031]: plci_change_state:0x101 8 -> 0 event=11
pppd[10031]: capiplugin: disconnect(remote): "" -> "001XXXXXXXXXX" outgoing (pcli=0x101/ncci=0x0) 0x3303 (0x0000) - Protocol error layer 3
pppd[10031]: plci_change_state:0x0 0 -> 1 event=1
pppd[10031]: capiplugin: dialing 001XXXXXXXXXX (hdlc)
pppd[10031]: plci_change_state:0x101 1 -> 2 event=3
pppd[10031]: DISCONNECT_IND reason 0x3303 (Protocol error layer 3) for plci 0x101
pppd[10031]: plci_change_state:0x101 2 -> 8 event=9
pppd[10031]: plci_change_state:0x101 8 -> 0 event=11
pppd[10031]: capiplugin: disconnect(remote): "" -> "001XXXXXXXXXX" outgoing (pcli=0x101/ncci=0x0) 0x3303 (0x0000) - Protocol error layer 3
pppd[10031]: plci_change_state:0x0 0 -> 1 event=1
pppd[10031]: capiplugin: dialing 001XXXXXXXXXX (hdlc)
pppd[10031]: plci_change_state:0x101 1 -> 2 event=3
pppd[10031]: DISCONNECT_IND reason 0x3303 (Protocol error layer 3) for plci 0x101
pppd[10031]: plci_change_state:0x101 2 -> 8 event=9
pppd[10031]: plci_change_state:0x101 8 -> 0 event=11
pppd[10031]: capiplugin: disconnect(remote): "" -> "001XXXXXXXXXX" outgoing (pcli=0x101/ncci=0x0) 0x3303 (0x0000) - Protocol error layer 3
pppd[10031]: capiplugin: couldn't make connection after 4 retries
pppd[10031]: controller 1: listen_change_state 0 -> 1
pppd[10031]: controller 1: listen_change_state state=1 event=1 ????
last message repeated 2 times
pppd[10031]: contr 1: listenconf Info=0x0000 (No additional information) infomask=0x144 cipmask=0x0 capimask2=0x0
pppd[10031]: controller 1: listen_change_state 1 -> 0
pppd[10031]: capiplugin: exit
pppd[10031]: Exit.


What else I need to consider?

Thanks,
ARIF

[/size]

i] Last edited by arif.zaman at 2009-11-19 13:15 [/i

hi
please refer to the following link:
http://www.occidopagus.nl/linux/capi.pdf

Original posted by Robert at 2009-11-19 15:07

hi
please refer to the following link:
http://www.occidopagus.nl/linux/capi.pdf

Hi Robert,

I already read out this document. Can you please check all my log why I'm getting the following error msg after initiating PPPD call?
[/font][/size] pppd[10031]: capiplugin: dialing 001XXXXXXXXXX (hdlc)
pppd[10031]: plci_change_state:0x101 1 -> 2 event=3
pppd[10031]: DISCONNECT_IND reason 0x3303 (Protocol error layer 3) for plci 0x101
pppd[10031]: plci_change_state:0x101 2 -> 8 event=9
pppd[10031]: plci_change_state:0x101 8 -> 0 event=11
pppd[10031]: capiplugin: disconnect(remote): "" ->"001XXXXXXXXXX" outgoing (pcli=0x101/ncci=0x0) 0x3303 (0x0000) - Protocol error layer 3

Thanks,
ARIF

hi
which kind of card do you use, is it OpenVOX card?

Here is my lspci output:

02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)
Subsystem: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S]
Flags: medium devsel, IRQ 177
I/O ports at c880 [\size=8]
Memory at cfbfe000 (32-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: [40] Power Management version 2

Thanks,
ARIF

hi
please send your ssh to me: This email address is being protected from spambots. You need JavaScript enabled to view it.