keywords: ip pbx voip gateway gsm gateway

× Questions about D-110P 1 Span E1/T1/J1 Interface Card

D110E and Red Alarm Problem

11 years 5 months ago #7197 by [email protected]
I installed a new D110E on a Dell Poweredge T110 box and installed Trixbox 1.8.0.4.

I removed the jumper on the card and configured for T1 PRI.

I am running this same configuration on another older server with a TE110p that I want to replace so I believe the configuration is correct. Everything works fine on the old box, but when I move the cable over to the new box, the blinking red alarm turns solid red and never goes to green.

Here is the output from diagnostic tools:

dahdi_scan:
[1]
active=yes
alarms=RED
description=Digium Wildcard TE110P T1/E1 Card 0
name=WCT1/0
manufacturer=Digium
devicetype=Digium Wildcard TE110P T1/E1
location=PCI Bus 02 Slot 01
basechan=1
totchans=24
irq=169
type=digital-T1
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI
framing_opts=ESF,D4
coding=B8ZS
framing=ESF

dahdi_hardware:
pci:0000:02:00.0 wcte11xp+ e159:0001 Digium Wildcard TE110P T1/E1 Board

lspci –v:
02:00.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 79fe:0001
Flags: bus master, medium devsel, latency 32, IRQ 169
I/O ports at fc00
Memory at df9fe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2

Cat /proc/interrupts:
CPU0 CPU1 CPU2 CPU3
0: 2152907 0 0 56767 IO-APIC-edge timer
8: 0 0 3 0 IO-APIC-edge rtc
9: 0 0 0 0 IO-APIC-level acpi
50: 6276 0 24662 0 PCI-MSI ahci
66: 256 0 0 2603 PCI-MSI eth1
169: 0 1976768 9367 0 IO-APIC-level wcte11xp
225: 0 0 123 271 IO-APIC-level ehci_hcd:usb1, ehci_hcd:usb2
NMI: 0 0 0 0
LOC: 2209432 2209432 2209431 2209431
ERR: 0
MIS: 0

dahdi_test:
Opened pseudo dahdi interface, measuring accuracy...
91.188% 91.524% 91.151% 91.709% 90.809% 91.258% 91.577% 91.163%
90.899% 91.006% 91.190% 90.696% 91.116% 91.630% 91.066% 91.574%
--- Results after 16 passes ---
Best: 91.709 -- Worst: 90.696 -- Average: 91.222375, Difference: 108.777625

Asterisk > dahdi show channels
Chan Extension Context Language MOH Interpret Blocked State
pseudo default en default In Service
1 from-pstn en default In Service
2 from-pstn en default In Service
3 from-pstn en default In Service
4 from-pstn en default In Service
5 from-pstn en default In Service
6 from-pstn en default In Service
7 from-pstn en default In Service
8 from-pstn en default In Service
9 from-pstn en default In Service
10 from-pstn en default In Service
11 from-pstn en default In Service
12 from-pstn en default In Service
13 from-pstn en default In Service
14 from-pstn en default In Service
15 from-pstn en default In Service
16 from-pstn en default In Service
17 from-pstn en default In Service
18 from-pstn en default In Service
19 from-pstn en default In Service
20 from-pstn en default In Service
21 from-pstn en default In Service
22 from-pstn en default In Service
23 from-pstn en default In Service

I assume the cable should be correct since it currently works on the TE110p card. Am I dealing with a hardware or hardware compatibility problem. Any advice or assistance would be most appreciated.


i] Last edited by skoubyej at 2011-8-3 01:57 [/i
11 years 5 months ago #7198 by [email protected]
One piece of additional information. I created a loopback cable and the card flashes red then green then back again in rapid succession. Don't know if this is much help or not.
11 years 5 months ago #7199 by [email protected]
I also noticed a typo in my original post. Trixbox is 2.8.0.4 not 1.8.0.4. Sorry for the confusion.
11 years 5 months ago #7200 by svolta
Hi,
There's maybe the hardware compatibility problem, please try our new product D130!
11 years 5 months ago #7201 by [email protected]
Are you suggesting that I return the D110E that I purchased in exchange? If so, can you direct me to the procedure for doing this? I am in the USA.
Time to create page: 0.033 seconds
Powered by Kunena Forum