D110P + Zaptel - Instalation problem

Greetings everyone.

I have a OpenVox D110P on a machine with the following software:
CentOS 5 / kernel 2.6.18-92.1.13.el5 / zaptel 1.4.12.1 / asterisk 1.6.0.1 / mISDN 1.1.8

I have also installed one A400P and one B400P, both installed correctly and running (though I still have some issues with B400P).

Now, the problem with D110P.

lspci -v tells me that the card is detected.

---

00:08.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device b100:0001
Flags: bus master, medium devsel, latency 64, IRQ 217
I/O ports at a800
Memory at d7efa000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2

00:09.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 79fe:0001
Flags: bus master, medium devsel, latency 64, IRQ 209
I/O ports at a400
Memory at d7ef9000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2

00:0a.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)
Subsystem: Cologne Chip Designs GmbH Unknown device e888
Flags: medium devsel, IRQ 10
I/O ports at a000
Memory at d7ef8000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2

---

I believe it's the first, judging by the order they are on the PCI sockets.

/etc/init.d/zaptel start

---

Loading zaptel framework: [ OK ]
Waiting for zap to come online...OK
Loading zaptel hardware modules: tor2.
wct4xxp.
wcte12xp.
wct1xxp.
wcte11xp.
wctdm24xxp.
wcfxo.
wctdm.
wcusb.
xpp_usb.
No hardware timing source found in /proc/zaptel, loading ztdummy
Running ztcfg: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
[FAILED]

---

Note: This error was happening before I connected D110P as well.

At last, ztcfg -vvvvvvvv:

---

Zaptel Version: 1.4.12.1
Echo Canceller: MG2
Configuration
======================


Channel map:

Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)

4 channels to configure.

ZT_CHANCONFIG failed on channel 1: No such device or address (6)

---

No sign of D110P here.

I have recompiled with make clean; make; make install; make config, but everything keeps the same.

Am I missing something? Does it need some patch like the PG version needs?

Thanks in advance.
-psantos

Problem solved.

Happens that I had netjetpci module loaded and that was causing a series of problems with zaptel and misdn.

So I unloaded it (modprobe -r netjetpci) and added it to the modules blacklist. After that I recompiled zaptel and ran genzaptelconf -sdvM and now everything is working as intended.

Best regards,
-psantos