- Thank you received: 0
- Forum
- End of Life Products Support
- D115 Series
- D110P PRI E1 card on Trixbox 2.8 and Dell T105 RED ALARM
×
Questions about D-110P 1 Span E1/T1/J1 Interface Card
D110P PRI E1 card on Trixbox 2.8 and Dell T105 RED ALARM
14 years 6 months ago #3847
by epatey
My modem wants this configuration:
Pin Description
1 not connected
2 not connected
3 RX +
4 TX +
5 TX -
6 RX -
7 not connected
8 not connected
However, I built a loopback cable (connects 1 to 4 and 2 to 5) and I still get a red alarm. Could this mean it is a hardware defect?
Pin Description
1 not connected
2 not connected
3 RX +
4 TX +
5 TX -
6 RX -
7 not connected
8 not connected
However, I built a loopback cable (connects 1 to 4 and 2 to 5) and I still get a red alarm. Could this mean it is a hardware defect?
14 years 6 months ago #3860
by epatey
For clarity, I'm posting my interrupts status. The card appears to be happy on its own interrupt:
[
[
root@trixbox1 proc]# cat interrupts
CPU0 CPU1
0: 706079 36068902 IO-APIC-edge timer
1: 0 3 IO-APIC-edge i8042
8: 0 1 IO-APIC-edge rtc
9: 0 0 IO-APIC-level acpi
12: 0 5 IO-APIC-edge i8042
50: 7053 393877 IO-APIC-level sata_nv
66: 34348 36694994 IO-APIC-level wcte11xp
98: 91400 0 PCI-MSI eth0
217: 0 3 IO-APIC-level ehci_hcd:usb1
225: 266 11799 IO-APIC-level ohci_hcd:usb2
233: 1035 53945 IO-APIC-level sata_nv
NMI: 0 0
LOC: 36774643 36777228
ERR: 0
MIS: 0
14 years 6 months ago #3862
by epatey
Okay. Thanks to the great support by Open Vox, I'm making progress. I made a custom cable and followed as described and now there is no alarm. My only problem now is this:
chan_dahdi.c:11722 pri_dchannel: PRI Error on span 0: We think we're the network, but they think they're the network, too.
this goes back and forth when i change from pri_cpe to pri_net, so I believe I might have the cable in a loopback when it wants a straight through connection.
chan_dahdi.c:11722 pri_dchannel: PRI Error on span 0: We think we're the network, but they think they're the network, too.
this goes back and forth when i change from pri_cpe to pri_net, so I believe I might have the cable in a loopback when it wants a straight through connection.
14 years 6 months ago #3863
by epatey
Well cable is correct and I'm still getting these errors. I'm setup as follows:
;
; DAHDI telephony
;
; Configuration file
;[trunkgroups]
[channels]
context=from-zaptel
switchtype=euroisdn
pridialplan=national
usecallerid=yes
hidecallerid=no
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
echocancel=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
callprogress=no
callerid=asreceived
group=1
signalling=pri_cpe
channel => 1-15,17-31
;Include setup-pstn configs
#include dahdi-channels.conf
;Include PBXconfig configs
#include chan_dahdi_additional.conf
and my system.conf is as follows:
# Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER)
span=1,0,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
echocanceller=mg2,1-15,17-31
# Global data
loadzone = es
defaultzone = es
Any ideas?
;
; DAHDI telephony
;
; Configuration file
;[trunkgroups]
[channels]
context=from-zaptel
switchtype=euroisdn
pridialplan=national
usecallerid=yes
hidecallerid=no
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
echocancel=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
callprogress=no
callerid=asreceived
group=1
signalling=pri_cpe
channel => 1-15,17-31
;Include setup-pstn configs
#include dahdi-channels.conf
;Include PBXconfig configs
#include chan_dahdi_additional.conf
and my system.conf is as follows:
# Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER)
span=1,0,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
echocanceller=mg2,1-15,17-31
# Global data
loadzone = es
defaultzone = es
Any ideas?
- Forum
- End of Life Products Support
- D115 Series
- D110P PRI E1 card on Trixbox 2.8 and Dell T105 RED ALARM
Time to create page: 0.041 seconds