IX100 and chan_misdn problem

Hi

Tried the last suggestion but no joy see demesg output

Modular ISDN Stack core version (1_1_8) revision ($Revision: 1.40 $)
mISDNd: kernel daemon started (current:cffd0a90)
mISDNd: test event done
cs5535_gpio: base=0x6100 mask=0xb003c66 major=253
mISDN: HFC-multi driver Rev. 1.68
Not enough 'protocol' values given.
hfc_multi: probe of 0000:00:0e.0 failed with error -22
0 devices registered
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
natsemi dp8381x driver, version 2.1, Sept 11, 2006
originally by Donald Becker <This email address is being protected from spambots. You need JavaScript enabled to view it.>
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
ieee80211_crypt: registered algorithm 'NULL'
geode-mfgpt: Registered timer 0
Registered led device: alix:1
Registered led device: alix:2
Registered led device: alix:3
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.4.12.1
Zaptel Echo Canceller: MG2
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: This email address is being protected from spambots. You need JavaScript enabled to view it.
eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth0: no IPv6 routers present
Registered Tormenta2 PCI
usbcore: registered new interface driver wcusb
Wildcard USB FXS Interface driver registered
INFO-xpp: revision trunk-r6058 MAX_XPDS=64 (8*
INFO-xpp: FEATURE: without BRISTUFF support
INFO-xpp: FEATURE: with PROTOCOL_DEBUG
INFO-xpp: FEATURE: with ECHO_SUPPRESSION
INFO-xpp: FEATURE: without XPP_EC_CHUNK
INFO-xpp: FEATURE: with sync_tick() from ZAPTEL
INFO-xpp_usb: revision trunk-r6058
usbcore: registered new interface driver xpp_usb
ztdummy: Trying to load High Resolution Timer
ztdummy: Initialized High Resolution Timer
ztdummy: Starting High Resolution Timer
ztdummy: High Resolution Timer started, good to go
Registered tone zone 4 (United Kingdom)
CAPI Subsystem Rev 1.1.2.8
capifs: Rev 1.1.2.3
capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
ISDN L1 driver version 1.20
ISDN L2 driver version 1.32
mISDN: DSS1 Rev. 1.47
mISDN Capi 2.0 driver file version 1.21
mISDN_dsp: Audio DSP Rev. 1.29 (debug=0x0) EchoCancellor MG2 dtmfthreshold(100)
mISDN_dsp: DSP clocks every 64 samples. This equals 8 jiffies.

Joseph

hello：
please check ISDN and boot it from right files. actually, the main idea is try to delay the hardware booting and make it to wait until the system recourse is ready. so i add sleep 10 in mISDN. it should work. please double check.
regards!
James.zhu

Hi

I don`t understand "check isdn"

I followed the instruction above

1). update-rc.d mISDN　defaults 25 30
2). edit the /etc/modprobe.d/mISDN
install hfcmulti /usr/sbin/mISDN start
remove hfcmulti /usr/sbin/mISDN stop

install hfcpci /usr/sbin/misdn-init start hfcpci
remove hfcpci /usr/sbin/misdn-init stop

install hfcsusb /usr/sbin/misdn-init start hfcsusb
remove hfcsusb /usr/sbin/misdn-init stop

install hfcsmini /usr/sbin/misdn-init start hfcsmini
remove hfcsmini /usr/sbin/misdn-init stop

install xhfc /usr/sbin/misdn-init start xhfc
remove xhfc /usr/sbin/misdn-init stop

install avmfritz /usr/sbin/misdn-init start avmfritz
remove avmfritz /usr/sbin/misdn-init stop

install w6692pci /usr/sbin/misdn-init start w6692pci
remove w6692pci /usr/sbin/misdn-init stop

install sedlfax /usr/sbin/misdn-init start sedlfax
remove sedlfax /usr/sbin/misdn-init stop

3). edit the mISDN file under /etc/init.d
function run_start_commands
{
local i=0
sleep 10 ; add 10 to wait the system is ready
echo "-- Loading mISDN modules --"
while [ ! -z "${START_COMMANDS[${i}]}" ]; do
echo ">> ${START_COMMANDS[${i}]}"
eval "${START_COMMANDS[${i}]}"
let "i = ${i} + 1"
done
}

But it still will not start at boot, we still have to stop mISDN and restart it manualy to get it going.

Joseph

hello:
please give me ssh account, i will check it. email the ssh to:[email protected].
regards!
James.zhu