[SOLVED] A800E trixbox 2.8.0.3 channe fxs no module

I have a new installation on a trixbox 2.8.0.3 of a A800E equiped with 5 FXS and 3 FXO interfaces.From Tel1 to Tel5 are the FXS.giving the command dahdi_genconf the system.conf is:# Span 1: OPVXA1200/12 "OpenVox A1200P/A800P Board 13" (MASTER) # channel 1, OPVXA1200/12/0, no module.# channel 2, OPVXA1200/12/1, no module.# channel 3, OPVXA1200/12/2, no module.# channel 4, OPVXA1200/12/3, no module.# channel 5, OPVXA1200/12/4, no module.fxsks=6echocanceller=mg2,6fxsks=7echocanceller=mg2,7fxsks=8echocanceller=mg2,8Why the system reconize the FXO and not the FXS?? i' going crazy, pls help me.. thanks. Paolo

i] Last edited by ptrenta at 2011-2-7 18:43 [/i

Please show me your dmesg information, did you connect the 12V power jack for A1200P? FXS modules need the 12V external power.

Yes, i know. I have connected the power cable and also tested with a voltmeter that was operating, but effectively the dmesg write that maybe i missed it!!.any idea??

Linux version 2.6.18-128.1.10.el5 (This email address is being protected from spambots. You need JavaScript enabled to view it.) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44))
...
...
dahdi: Telephony Interface Registered on major 196
dahdi: Version: 2.2.0
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 169
OpenVox A800P version: 1.4
OpenVox A800P passed register test
ProSLIC on module 0 failed to powerup within 501 ms (0 mV only)


-- DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE A1200P??
Unable to do INITIAL ProSLIC powerup on module 0
Init ProSlic with Manual Calibration
Unable to do INITIAL ProSLIC powerup on module 0
Module 0: FAILED FXS (FCC)
Unable to do INITIAL ProSLIC powerup on module 1
Init ProSlic with Manual Calibration
Unable to do INITIAL ProSLIC powerup on module 1
Module 1: FAILED FXS (FCC)
Unable to do INITIAL ProSLIC powerup on module 2
Init ProSlic with Manual Calibration
Unable to do INITIAL ProSLIC powerup on module 2
Module 2: FAILED FXS (FCC)
Unable to do INITIAL ProSLIC powerup on module 3
Init ProSlic with Manual Calibration
Unable to do INITIAL ProSLIC powerup on module 3
Module 3: FAILED FXS (FCC)
Unable to do INITIAL ProSLIC powerup on module 4
Init ProSlic with Manual Calibration
Unable to do INITIAL ProSLIC powerup on module 4
Module 4: FAILED FXS (FCC)
Module 5: Installed -- AUTO FXO (FCC mode)
Module 6: Installed -- AUTO FXO (FCC mode)
Module 7: Installed -- AUTO FXO (FCC mode)
floppy0: no floppy controllers found
Found aa OpenVox A800P: Version 1.4 (3 modules)
buffer sync misseed!
buffer re-sync occur from -1 to 3
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
...


...

Solved. In effect the problem was of power supply ..there is a jumper to set on J916 in ext position.I suggest to update the wiki 'cause i could not find any documentation about that J916 i've just tried it!!!And i could save 2 working days around that problem..

thanks.. regards.Paolo

i] Last edited by ptrenta at 2011-2-7 18:44 [/i