Don't hangup incomming calls

Hello!

Ihave a problem with A400P.

Fails to hangup incoming calls.Finally, I find the time that this happens

Outgoing call from asterisk works.

Incoming call frompots
Remote party hangs up. Card do a disconnect. Every thingworks like a charm.
Asterisk user hangs up, No disconnect. Untilremote party hangs up. Then i get a disconnect and asterisk see it asnew incoming call.


Is this issuerelated to the card or the driver?

Any suggestions.

/Fjonson


Cardboot
dahdi: Telephony InterfaceRegistered on major 196
dahdi: Version: 2.4.0
ALAW overrideparameter detected. Device will be operating in ALAW
dahdi:Registered Span 1 ('WCTDM/4') with 4 channels
dahdi: Span('WCTDM/4') is new master
Freshmaker version: 71
Freshmakerpassed register test
ProSLIC on module 0, product 0, version0
Module 0: Not installed
ProSLIC on module 1, product 0,version 0
VoiceDAA System: 04
ISO-Cap is now up, line side: 03rev 06
setting FXO tx gain for card=1 to 0
setting FXO rx gainfor card=1 to 0
DEBUG fxotxgain:0.0 fxorxgain:0.0
Module 1:Installed -- AUTO FXO (SWEDEN mode)
ProSLIC on module 2, product0, version 0
Module 2: Not installed
ProSLIC on module 3,product 0, version 0
Module 3: Not installed
Found a WildcardTDM: Wildcard TDM400P REV E/F (1 modules)
2295230744 Polarityreversed (0 -> 1)
BATTERY on 1/2 (+)!
dahdi: Registered tonezone 0 (United States / North America)
BATTERY on 1/2(+)!
dahdi_echocan_mg2: Registered echo canceler 'MG2'
dahdi:Registered tone zone 16 (Sweden)

Incommingcall no answer (OK)
2295356783Polarity reversed (1 -> -1)
2295359055Polarity reversed (-1 -> 1)
RING on 1/2!
NO RING on1/2!
RING on 1/2!
NO RING on 1/2!

Incommingcall remote party hangs up.(OK)
2295420266Polarity reversed (1 -> -1)
2295422522 Polarity reversed (-1 ->1)
RING on 1/2!
NO RING on 1/2!
2295427323 Polarity reversed(1 -> -1)
2295448831 Polarity reversed (-1 -> 1)

Incommingcall asterisk user hangs up.(FAIL)
2295512826Polarity reversed (1 -> -1)
2295515098 Polarity reversed (-1 ->1)
RING on 1/2!
NO RING on 1/2!
2295519851 Polarity reversed(1 -> -1)
Asterisk user did a hang up

This is recivethen remote user did hangup
2295541215 Polarity reversed (-1 ->1)

Hi,
You can try enabling or adding 'busydetect=yes' and 'busycount=3' in /etc/asterisk/chan_dahdi.conf.

Hello.

Already done this. No difference.

I can not understand what the difference would be when there is no signaling on the line before the remote receiver hangs up.

It feels like something is missing on incoming calls, the card gets into the wrong position/mode
, when everything is working properly if I phone.

[channels]
language=se
usecallerid=yes
cidsignalling=dtmf
cidstart=polarity
hidecallerid=no
callwaiting=yes
restrictcid=no
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
relaxdtmf=no
immediate=no
callerid = asreceived
useincomingcalleridondahditransfer = yes
busydetect=yes
busycount=5
busypattern=250,250
answeronpolarityswitch=yes
hanguponpolarityswitch=yes
progzone=se
usedistinctiveringdetection=yes

Hi,
Maybe there's no polarity reversed on your pstn line, your can try disabling 'answeronpolarityswitch=yes' and 'hanguponpolarityswitch=yes'.

Sorry was not as successful. Still the same problem.
The side effect was that asterisk does not disconnect when the recipient hangs up.

Sitting and looking for the error. The main difference between a dial-up call and the call received is that I get Polarity reversed on incoming calls before Hook off.
I do not know if it matters.

More debug in wctdm

Outgoing
Hook off chan 1
Hook off chan 1
2625907 Polarity reversed (1 -> -1)
Hook on chan 1
2636437 Polarity reversed (-1 -> 1)

Incomming
4130010 Polarity reversed (1 -> -1)
4132299 Polarity reversed (-1 -> 1)
RING on 1/2!
NO RING on 1/2!
Hook off chan 1
4136684 Polarity reversed (1 -> -1)
Hook on chan 1
4158399 Polarity reversed (-1 -> 1)

Hi,
Please try disabling 'busypattern=250,250' and adjusting the value of 'busycount=' to '3'. If the problem still there, please send me the ssh, I will check it for you! My Emai: This email address is being protected from spambots. You need JavaScript enabled to view it.