A800P not working with Elastix 2.2

Hi I just bought 5 cards A800P (v1.2) and installed them in a fresh installation of Elastix 2.2.

The hardware I am using is a Jetway M/b (JNC9C-5500LF) with Intel Dual Core Atom My setup is 4FXO modules and 2FXS Modules. The card is recognised by te system and I can make outgoing calls only in the first 4 modules. I can ring the FXS modules but when I pickup the phone it is full of noise!!!. I switched the FXS modules with 2 of the FXO modules and now the 2 FXO's are not working (again horrible noise)!!! Also the calls i am alble to complete from the first 4 have a lot of noise which is also heard on the other side.

I tried almost everything....

Please help I have to make these systems as soon as possible. bellow is my config:

System.conf

# Span 1: OPVXA1200/12 "OpenVox A1200P/A800P Board 13" (MASTER)
fxsks=1
echocanceller=oslec,1
fxoks=2
echocanceller=oslec,2
fxsks=3
echocanceller=oslec,3
fxoks=4
echocanceller=oslec,4
fxsks=5
echocanceller=oslec,5
fxsks=6
echocanceller=oslec,6
# channel 7, OPVXA1200/12/6, no module.
# channel 8, OPVXA1200/12/7, no module.
# Global data
loadzone = us
defaultzone = us


Chan_dahdi.conf

[channels]
context=from-pstn
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
faxdetect=incoming
echotraining=800
rxgain=0.0
txgain=0.0
callgroup=1
pickupgroup=1
relaxdtmf=yes
;Uncomment these lines if you have problems with the disconection of your analog lines
;busydetect=yes
;busycount=3
　
immediate=no


Dahdi-channels.conf

; Span 1: OPVXA1200/12 "OpenVox A1200P/A800P Board 13" (MASTER)
;;; line="1 OPVXA1200/12/0 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 1
callerid=
group=
context=default
;;; line="2 OPVXA1200/12/1 FXOKS"
signalling=fxo_ks
callerid="Channel 2" <4002>
mailbox=4002
group=5
context=from-internal
channel => 2
callerid=
mailbox=
group=
context=default
;;; line="3 OPVXA1200/12/2 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 3
callerid=
group=
context=default
;;; line="4 OPVXA1200/12/3 FXOKS"
signalling=fxo_ks
callerid="Channel 4" <4004>
mailbox=4004
group=5
context=from-internal
channel => 4
callerid=
mailbox=
group=
context=default
;;; line="5 OPVXA1200/12/4 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 5
callerid=
group=
context=default
;;; line="6 OPVXA1200/12/5 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 6
callerid=
group=
context=default
　
　

If the version of the firmware on A1200 is 1.6, you must download the driver from this link:
http://downloads.openvox.cn/pub/drivers/dahdi-linux-complete/releases/1.3.3/
Pls confirm that and tell me the result.
BTW, after you installed the driver, you have to cut the power of your server then start again.

Yes the firmware is 1.6!!! I will try it and let you know about the results. I reckon I have to download the version of my dahdi correct?

It worked!!! Thhank you very much. If I have other problems will let you know.

Best Regards,

Hi I have another issue and I was wondering if you can help me.

When I use the pstn lines I am expieriencing a delay of about 5 seconds before the call is completed. By that I mean that the call is done by elastix and it stays idle for 5 seconds until you hear the other side ring!!! is it possible to give me a hint?

Hi,
When did it happen? Inbound or outbound calls?
If inbound call, pls notice if it is because of the CID detecting? you can disable CID and have a try.
Paste the full log msg here with debug on, and chan_dahdi.conf.
Good luck.