Any instructions to install my A1200P in Elastix?

hello, Sir:
when you install elaxtix-0.9 for first time, please run:lspci -vvvvv and genzaptelconf first. have you done it?
Regards!
James.zhu

Thak you very much mr Zhu.
I didn´t do it at the first time, but now doesn´t work.
I will install again all the Elastix and in the first boot i will do the things you wrote.
I´ll keep you informed... .Thank you very much again...

PS: Do you know why www.elastix.org doesn´t work since last Friday ¿?

Hi there.
I made a new instalation, and still without working.
The first thing i did was lspci -vvvvv and genzaptelconf.
Any other ideas?
Thank you

hello, jsalinasf:
usually, if the card does not work, please check the few things:
1) one is that make sure the system can find a card, use lspci -vvvvv, can see the card info.
2) second, may be the zaptel.conf and zapata.conf are not correct. do a double tasks, after genzaptelconf -d command, please check the zaptel.conf again. sometimes, the zaptelconf generated by that command is not reliable.
3) run ztcfg -vvvv and dmesg, if all info is ok, you still can not make calls, please check extensions.conf and zapata.conf, make sure the info in two files are matched.
4) make sure zapata can be load, in asterisk console: help command will show zap info if your zapata.conf is ok and also show your modules: zap show channels.
regarding Elastix, i am not very sure why the some resource in Elastix website can not access. anyway, keep doing it and keep in touch with us.
Regards!
James.zhu

Dear Mr. Zhu...

on lspci -vvvvv
0a:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 95d9:0003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 4000
Region 1: Memory at efa00000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+


After that....

[root@pbx /]# genzaptelconf -d
[root@pbx /]# cat /etc/zaptel.conf
# Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#

# It must be in the module loading order


# Global data

loadzone = us
defaultzone = us

[root@pbx /]# ztcfg -vvvv

Zaptel Version: 1.4.6
Echo Canceller: OSLEC
Configuration
======================


Channel map:


0 channels to configure.

and with dmesg....

...
Zapata Telephony Interface Unloaded
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.4.6
Zaptap registered 'sample' char driver on major 33
Registered Tormenta2 PCI
Unregistered Tormenta2
Specify address with base=0xNNNNN
usbcore: registered new driver wcusb
Wildcard USB FXS Interface driver registered
usbcore: deregistering driver wcusb
INFO-xpp: revision branch-rel-4816-r4900 MAX_XPDS=64 (8*
INFO-xpp: FEATURE: with ECHO_SUPPRESSION
INFO-xpp: FEATURE: without XPP_EC_CHUNK
INFO-xpp: FEATURE: without BRISTUFF support
INFO-xpp: FEATURE: with sync_tick() from ZAPTEL
INFO-xpp: FEATURE: with PROTOCOL_DEBUG
INFO-xpp_usb: revision branch-rel-4816-r4900
usbcore: registered new driver xpp_usb
usbcore: deregistering driver xpp_usb
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)


in other way , i´m trying to compile the zaptel modules again, but i don´t know how to put the kernel-devel....

[root@pbx zaptel-1.4.7.1]# make
grep: /lib/modules/2.6.18-8.el5/build/include/linux/autoconf.h: No such file or
directory
grep: /lib/modules/2.6.18-8.el5/build/include/linux/autoconf.h: No such file or
directory
make[1]: Entering directory `/usr/src/zaptel-1.4.7.1'
You do not appear to have the sources for the 2.6.18-8.el5 kernel installed.
make[1]: *** [modules] Error 1
make[1]: Leaving directory `/usr/src/zaptel-1.4.7.1'
make: *** [all] Error 2

[root@pbx zaptel-1.4.7.1]# yum install kernel-devel
Loading "installonlyn" plugin
Setting up Install Process
Setting up repositories
base 100% |=========================| 1.1 kB 00:00
updates 100% |=========================| 951 B 00:00
addons 100% |=========================| 951 B 00:00
extras 100% |=========================| 1.1 kB 00:00
Reading repository metadata in from local files
Excluding Packages from CentOS-5 - Base
Finished
Excluding Packages from CentOS-5 - Updates
Finished
Excluding Packages from CentOS-5 - Addons
Finished
Excluding Packages from CentOS-5 - Extras
Finished
Parsing package install arguments
Nothing to do
[root@pbx zaptel-1.4.7.1]#
[root@pbx zaptel-1.4.7.1]# uname -r
2.6.18-8.el5


But in trixbox works perfectly....
Any help ?
Thank you very much

hello, Sir:
according the post, i think your zaptel.conf has nothing in side. please check it again. it should be added in after running: genzaptelconf -d, but you have no lucky. let's say we have 2 A1200P, the FXO and FXS should be like this:
# span 1: OPVXA1200/0 "OpenVox A1200P Board 1"
fxsks=1
fxsks=2
fxsks=3
fxsks=4
fxoks=5
fxoks=6
fxoks=7
fxoks=8
fxoks=9
fxoks=10
fxoks=11
fxoks=12
# Span 2: OPVXA1200/0 "OpenVox A1200P Board 2"
fxoks=13
fxoks=14
fxoks=15
fxoks=16
fxoks=17
fxoks=18
fxoks=19
fxoks=20
fxoks=21
fxoks=22
fxoks=23
fxoks=24

the simple way is that you copy the zaptel.conf generated by trixbox and post it into /etc/zaptel.conf
once again, please check zaptel.conf first when running ztcfg --- and zapata.conf when running asterisk -vvvvvvvgc.
Good luck!
James.zhu