A800P+FXS = no tone

Hello !

I have installed A800P + FSX module into PCI slot. zaptel correctly detects board:
OpenVox A1200P version: 1.2
OpenVox A1200P passed register test
Timeout waiting for calibration of module 0
Timeout waiting for calibration of module 0
Proslic Failed on Second Attempt to Auto Calibrate
Init ProSlic with Manual Calibration
Module 0: Installed -- MANUAL FXS
Module 1: Not installed
Module 2: Not installed
Module 3: Not installed
Module 4: Not installed
Module 5: Not installed
Module 6: Not installed
Module 7: Not installed
Module 8: Not installed
Module 9: Not installed
Module 10: Not installed
Module 11: Not installed
Found a OpenVox A1200P: Version 1.2 (1 modules)
buffer re-sync occur from 0 to 1
Registered tone zone 0 (United States / North America)
Zaptel Transcoder support loaded

ztcfg -vvvv show following:

Zaptel Version: 1.4.7.1
Echo Canceller: MG2
Configuration
======================


Channel map:

Channel 01: FXO Kewlstart (Default) (Slaves: 01)

1 channels to configure.

I'm running "./fxstest /dev/zap/1 stats" and I see following:
TIP: 0.0000 Volts
RING: 0.0000 Volts
VBAT: -8.6480 Volts

Why RING voltage is null ? Also I don't hear "tone" when phone is connected.

Then I have started "asterisk -vvvv". I see following lines:
== Parsing '/etc/asterisk/zapata.conf': Found
-- Registered channel 1, FXO Kewlstart signalling
-- Automatically generated pseudo channel

"asterisk -r" console shows following:
*CLI> zap show channels
Chan Extension Context Language MOH Interpret
pseudo default default
1 default default

*CLI> zap show channel 1
Channel: 1amer*CLI>
File Descriptor: 22
Span: 1
Extension:
Dialing: no
Context: default
Caller ID:
Calling TON: 0
Caller ID name:
Destroy: 0
InAlarm: 0
Signalling Type: FXO Kewlstart
Radio: 0
Owner: <None>
Real: <None>
Callwait: <None>
Threeway: <None>
Confno: -1
Propagated Conference: -1
Real in conference: 0
DSP: no
Relax DTMF: no
Dialing/CallwaitCAS: 0/0
Default law: ulaw
Fax Handled: no
Pulse phone: no
Echo Cancellation: 128 taps, currently OFF
Actual Confinfo: Num/0, Mode/0x0000
Actual Confmute: No
Hookstate (FXS only): Onhook

And I also don't hear any tone in my phone.
What is the problem ? Please, help.

Thanks !

hello, aospan:
have you check the power on board and connection? maybe you swap it?
Regards!
james.zhu

[quote:18b71839c9="james.zhu"]hello, aospan:
have you check the power on board and connection? maybe you swap it?
Regards!
james.zhu[/quote]

Power is connected to the borad. I'm powering HDD (seagate 750 GB) by the same power connector ...

As I understand "./fxstest /dev/zap/1 stats" must show some voltage on RING/TIP row even if asterisk is not started ? When asterisk is started I'v got:

./fxstest /dev/zap/1 stats
Unable to open /dev/zap/1: Device or resource busy

hello, you are online, please post the zaptel.conf here.
Regards!
James.zhu

cat /etc/zaptel.conf
# Autogenerated by ./genzaptelconf -- do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#

# It must be in the module loading order


# Span 1: OPVXA1200/0 "OpenVox A1200P Board 1"
fxoks=1
# channel 2, WCTDM, no module.
# channel 3, WCTDM, no module.
# channel 4, WCTDM, no module.
# channel 5, WCTDM, no module.
# channel 6, WCTDM, no module.
# channel 7, WCTDM, no module.
# channel 8, WCTDM, no module.
# channel 9, WCTDM, no module.
# channel 10, WCTDM, no module.
# channel 11, WCTDM, no module.
# channel 12, WCTDM, no module.

# Global data

loadzone = us
defaultzone = us

I'v made mistake. One screw-bolt in my computer case is close to A800P board ... ;( I have removed this bolt and everything is go fine. I can see not zero voltage on board:

./fxstest /dev/zap/1 stats
TIP: -5.6400 Volts
RING: -53.3920 Volts
VBAT: -62.4160 Volts

Also I can make calls vi asterisk.
Thanks for help !