A1200P Wont dial!

hi!!

its in normal status and the first log that i have sent its when the card doesnt made calls the last log that i sent its in normal status (one or two calls) we are talking about the customer performs 567 or 800 calls per day

When your system down, please run cat /proc/interrupts. This command will show you the times of interrupt each device driver handled.

Please run this command once, and copy the result , after 10 seconds, run this command again, then you can see how many interrupts happened in the past 10 seconds. if it was not nearly 1000 times/sec, It might be a h/w issue.

Hi zhu i have changed the mother board and in my messages log i got this results

Feb 8 20:57:16 bpaasesores kernel: Freed a OpenVox A1200 card
Feb 8 20:57:16 bpaasesores kernel: Unregistered Tormenta2
Feb 8 20:57:16 bpaasesores kernel: Zapata Telephony Interface Unloaded
Feb 8 20:57:16 bpaasesores kernel: Zapata Telephony Interface Registered on major 196
Feb 8 20:57:16 bpaasesores kernel: Zaptel Version: 1.2.23
Feb 8 20:57:16 bpaasesores kernel: Zaptel Echo Canceller: MG2
Feb 8 20:57:16 bpaasesores zaptel: Loading zaptel framework: succeeded
Feb 8 20:57:25 bpaasesores kernel: ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 193
Feb 8 20:57:25 bpaasesores kernel: OpenVox A1200P version: 1.2
Feb 8 20:57:25 bpaasesores kernel: OpenVox A1200P passed register test
Feb 8 20:57:25 bpaasesores kernel: Module 0: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 1: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 2: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 3: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 4: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 5: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 6: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 7: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 8: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:25 bpaasesores kernel: Module 9: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:26 bpaasesores kernel: Module 10: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:26 bpaasesores kernel: Module 11: Installed -- AUTO FXO (FCC mode)
Feb 8 20:57:26 bpaasesores kernel: Found a OpenVox A1200P: Version 1.2 (12 modules)
Feb 8 20:57:26 bpaasesores kernel: buffer re-sync occur from 0 to 3
Feb 8 20:57:26 bpaasesores kernel: Registered tone zone 0 (United States / North America)
Feb 8 20:57:28 bpaasesores kernel: Registered tone zone 0 (United States / North America)
Feb 8 20:57:28 bpaasesores zaptel: Running ztcfg: succeeded
Feb 8 20:57:33 bpaasesores kernel: Registered tone zone 0 (United States / North America)

the "buffer resync ocur its ok??? cause i got a lot of troubles i bought a

Gigabyte GA-945GCM-S2C

new and i setup all again

and i cat the proc messages within 10 seconds and i got this results

[root@bpaasesores log]# cat /proc/interrupts
CPU0
0: 82938152 IO-APIC-edge timer
8: 280 IO-APIC-edge rtc
9: 0 IO-APIC-level acpi
14: 224496 IO-APIC-edge ide0
15: 10 IO-APIC-edge libata
169: 233 IO-APIC-level HDA Intel, uhci_hcd
185: 2 IO-APIC-level ehci_hcd, uhci_hcd
193: 83000626 IO-APIC-level uhci_hcd, opvxa1200
201: 0 IO-APIC-level uhci_hcd
209: 757865 IO-APIC-level eth0
NMI: 0
LOC: 81670604
ERR: 0
MIS: 0


[root@bpaasesores log]# cat /proc/interrupts
CPU0
0: 82965349 IO-APIC-edge timer
8: 280 IO-APIC-edge rtc
9: 0 IO-APIC-level acpi
14: 224545 IO-APIC-edge ide0
15: 10 IO-APIC-edge libata
169: 233 IO-APIC-level HDA Intel, uhci_hcd
185: 2 IO-APIC-level ehci_hcd, uhci_hcd
193: 83027844 IO-APIC-level uhci_hcd, opvxa1200
201: 0 IO-APIC-level uhci_hcd
209: 758045 IO-APIC-level eth0
NMI: 0
LOC: 81697408
ERR: 0
MIS: 0


it should be fine now my asterisk card????

hello, rfernandez_mx:
the difference of interrupts is so big. difference of interrupts between 83027844 and 83000626 is more than 20000? how many cards are there in PC? if possible, please give us the ssh account to check for you.
Regards,
James.zhu

i sent you via email the user password and host by the subject

user ssh for the OPENVOX A1200P WONT DIAL

This email address is being protected from spambots. You need JavaScript enabled to view it.

hi zhu by the way i have changed the main board and i have these interrupts:

[root@bpaasesores ~]# cat /proc/interrupts
CPU0
0: 1167143 IO-APIC-edge timer
8: 1 IO-APIC-edge rtc
9: 0 IO-APIC-level acpi
14: 6434 IO-APIC-edge ide0
169: 1102236 IO-APIC-level opvxa1200
177: 11 IO-APIC-level libata
185: 591 IO-APIC-level ehci_hcd, uhci_hcd, uhci_hcd, uhci_hcd, uhci_hcd
193: 0 IO-APIC-level VIA8233
201: 3786 IO-APIC-level eth0
NMI: 0
LOC: 1167072
ERR: 0
MIS: 0
[root@bpaasesores ~]# cat /proc/interrupts
CPU0
0: 1171149 IO-APIC-edge timer
8: 1 IO-APIC-edge rtc
9: 0 IO-APIC-level acpi
14: 6434 IO-APIC-edge ide0
169: 1106241 IO-APIC-level opvxa1200
177: 11 IO-APIC-level libata
185: 591 IO-APIC-level ehci_hcd, uhci_hcd, uhci_hcd, uhci_hcd, uhci_hcd
193: 0 IO-APIC-level VIA8233
201: 3851 IO-APIC-level eth0
NMI: 0
LOC: 1171079
ERR: 0
MIS: 0