1. i installed A1200 with modules 1-6 FXOs and modules 7-12 FXS
2. i installated elastix 0.9.2.4
3. after installation, i did a check new hardware from elastix GUI
4. elastix found the first 6 fxo but label the last 6 as fxo instead of fxs
5. i went to zaptelc.conf and only first 6 fxos were found, so i added the
fxoks my self
; Including file containing the suggested configuration
; generated by the hardware detector tool
; Remove this line if you don't want this feature
#include zapata-channels.conf;
#include zapata_additional.conf
ztcfg -vvv reported fine
[root@elastix asterisk]# ztcfg -vvv
i went ahead to configure my extensions using freepbx.
when i try to call into that zap extensions. asterisk is telling
me no such zap.
i later did a fresh install with Trixbox / Openvox version with another A-1200P card with 5FXO and 4FXS
All FXO are detected except for some FXS with have the following ;
Mar 18 12:02:02 asterisk1 kernel: PCI: Found IRQ 10 for device 0000:01:04.0
Mar 18 12:02:02 asterisk1 kernel: PCI: Sharing IRQ 10 with 0000:00:02.0
Mar 18 12:02:02 asterisk1 kernel: PCI: Sharing IRQ 10 with 0000:00:1f.1
Mar 18 12:02:09 asterisk1 kernel: OpenVox A1200P version: 1.2
Mar 18 12:02:09 asterisk1 kernel: OpenVox A1200P passed register test
Mar 18 12:02:09 asterisk1 kernel: Module 0: Installed -- AUTO FXO (FCC mode)
Mar 18 12:02:09 asterisk1 kernel: Module 1: Installed -- AUTO FXO (FCC mode)
Mar 18 12:02:09 asterisk1 kernel: Module 2: Installed -- AUTO FXO (FCC mode)
Mar 18 12:02:09 asterisk1 kernel: Module 3: Installed -- AUTO FXO (FCC mode)
Mar 18 12:02:09 asterisk1 kernel: Module 4: Installed -- AUTO FXO (FCC mode)
Mar 18 12:02:09 asterisk1 kernel: Module 5: Installed -- AUTO FXS/DPO
Mar 18 12:02:09 asterisk1 kernel: Module 6: Installed -- AUTO FXS/DPO
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should be 1000
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! COMMON_MAX_TRES iREG 1F = 0 should be 200
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = 1480 should be 7C0
Mar 18 12:02:09 asterisk1 zaptel: Loading opvxa1200: succeeded
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! PWR_ALARM_Q3Q4 iREG 21 = 37C0 should be 2600
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! PWR_ALARM_Q5Q6 iREG 22 = 3D70 should be 1B80
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! LOOP_CLOSURE_FILTER iREG 23 = 3970 should be 8000
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 78E0 should be 320
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! TERM_LP_POLE_Q1Q2 iREG 25 = 8B60 should be 8C
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! TERM_LP_POLE_Q3Q4 iREG 26 = 6A40 should be 100
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! TERM_LP_POLE_Q5Q6 iREG 27 = 8070 should be 10
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! CM_BIAS_RINGING iREG 28 = FFFF should be C00
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! DCDC_MIN_V iREG 29 = FFFF should be C00
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! DCDC_XTRA iREG 2A = FFFF should be 1000
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! LOOP_CLOSE_TRES_LOW iREG 2B = FFFF should be 1000
Mar 18 12:02:09 asterisk1 kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY.
Mar 18 12:02:09 asterisk1 kernel: Indirect Registers failed verification.
Mar 18 12:02:09 asterisk1 kernel: Init ProSlic with Manual Calibration
Mar 18 12:02:09 asterisk1 kernel: Proslic Failed on Second Attempt to Calibrate Manually. (Try -DNO_CALIBRATION in Makefile)
Mar 18 12:02:09 asterisk1 kernel: Module 7: FAILED FXS (FCC)
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should be 1000
Mar 18 12:02:09 asterisk1 zaptel: Loading wct4xxp: succeeded
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! COMMON_MAX_TRES iREG 1F = 0 should be 200
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = 1480 should be 7C0
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! PWR_ALARM_Q3Q4 iREG 21 = 37C0 should be 2600
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! PWR_ALARM_Q5Q6 iREG 22 = 3D70 should be 1B80
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! LOOP_CLOSURE_FILTER iREG 23 = 3970 should be 8000
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 78E0 should be 320
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! TERM_LP_POLE_Q1Q2 iREG 25 = 8B60 should be 8C
Mar 18 12:02:09 asterisk1 zaptel: Loading wct1xxp: succeeded
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! TERM_LP_POLE_Q3Q4 iREG 26 = 6A40 should be 100
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! TERM_LP_POLE_Q5Q6 iREG 27 = 8070 should be 10
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! CM_BIAS_RINGING iREG 28 = FFFF should be C00
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! DCDC_MIN_V iREG 29 = FFFF should be C00
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! DCDC_XTRA iREG 2A = FFFF should be 1000
Mar 18 12:02:09 asterisk1 zaptel: Loading wcte11xp: succeeded
Mar 18 12:02:09 asterisk1 kernel: !!!!!!! LOOP_CLOSE_TRES_LOW iREG 2B = FFFF should be 1000
Mar 18 12:02:09 asterisk1 kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY.
Mar 18 12:02:09 asterisk1 kernel: Indirect Registers failed verification.
Mar 18 12:02:09 asterisk1 zaptel: Loading wcfxo: succeeded
Mar 18 12:02:09 asterisk1 kernel: Init ProSlic with Manual Calibration
Mar 18 12:02:09 asterisk1 kernel: Proslic Failed on Second Attempt to Calibrate Manually. (Try -DNO_CALIBRATION in Makefile)
Mar 18 12:02:09 asterisk1 kernel: Module 8: FAILED FXS (FCC)
Mar 18 12:02:09 asterisk1 kernel: Module 9: Not installed
Mar 18 12:02:09 asterisk1 kernel: Module 10: Not installed
Mar 18 12:02:09 asterisk1 kernel: Module 11: Not installed
Mar 18 12:02:09 asterisk1 kernel: Found a OpenVox A1200P: Version 1.2 (7 modules)
what am i doing wrong here?
cant be the FXS and i dont think is the A1200P card as well. i have with me 2 units of A1200P and still some FXS are not detecting