keywords:pbx ip pbx voip gateway gsm gateway

× Questions about B100/200/400/800 ISDN BRI Cards

2x B400P...invalid sync priority

8 years 7 months ago #6500 by vmiro
I got two B400P in Dell PE750 and I can't dial or receive calls...when I type "dmesg" in console I get some confusing messages:

wcb4xxp 0000:03:03.0: Span 5 has invalid sync priority (5), removing from sync source list
wcb4xxp 0000:03:03.0: Span 6 has invalid sync priority (6), removing from sync source list
wcb4xxp 0000:03:03.0: Span 7 has invalid sync priority (7), removing from sync source list
wcb4xxp 0000:03:03.0: Span 8 has invalid sync priority (8), removing from sync source list
dahdi_echocan_oslec: Registered echo canceler 'OSLEC'
dahdi: Registered tone zone 0 (United States / North America)
wcb4xxp 0000:02:01.0: new card sync source: port 1
wcb4xxp 0000:03:03.0: Span 5 has invalid sync priority (5), removing from sync source list
wcb4xxp 0000:03:03.0: Span 6 has invalid sync priority (6), removing from sync source list
wcb4xxp 0000:03:03.0: Span 7 has invalid sync priority (7), removing from sync source list
wcb4xxp 0000:03:03.0: Span 8 has invalid sync priority (8), removing from sync source list
wcb4xxp 0000:03:03.0: Span 5 has invalid sync priority (5), removing from sync source list
wcb4xxp 0000:03:03.0: Span 6 has invalid sync priority (6), removing from sync source list
wcb4xxp 0000:03:03.0: Span 7 has invalid sync priority (7), removing from sync source list
wcb4xxp 0000:03:03.0: Span 8 has invalid sync priority (8), removing from sync source list
All TDMoE multiframe span groups are active.
wcb4xxp 0000:03:03.0: Span 5 has invalid sync priority (5), removing from sync source list
wcb4xxp 0000:03:03.0: Span 6 has invalid sync priority (6), removing from sync source list
wcb4xxp 0000:03:03.0: Span 7 has invalid sync priority (7), removing from sync source list
wcb4xxp 0000:03:03.0: Span 8 has invalid sync priority (8), removing from sync source list
...
dahdi: Master changed to B4/1/1
dahdi: Master changed to B4/0/2
dahdi: Master changed to B4/1/1
dahdi: Master changed to B4/0/2
dahdi: Master changed to B4/1/1
dahdi: Master changed to B4/0/2

What this means, are these a regular messages...?
I've set the CardID...
Card1: off, off, off, off
Card2: on, off, off, off
According to the manual there are three CardID switches, but on the card there are four, so I set the last one to OFF.

I'm using Elastix 2.0.3.

Thanks
mIRO
8 years 7 months ago #6504 by Denins.Den
the right way is
card1: on, on, on, on
card2: off, on, on, on

please try!
8 years 7 months ago #6508 by vmiro
I got the outgoing and incoming calls working, but I got the same messages...I hope it is normal!
You should change the jumper settings in the B400P manual... ;) ('off' instead of 'on')

Thanks ;)
mIRO
Time to create page: 0.020 seconds
Powered by Kunena Forum